V1, VR and V2 are the three speeds that govern every takeoff you will ever fly — and they are among the most heavily examined topics in EASA ATPL 032 Performance. Yet they are also widely misunderstood: V1 is routinely mislabelled, VR is confused with the stall speed, and V2's relationship with the control speeds VMCG and VMCA is where strong candidates separate themselves from the rest. This guide fixes all three.

Why the V-speeds exist
Every takeoff is a trade between distance and safety. Accelerate longer and you use more runway; rotate earlier and you climb away slower, closer to the stall, with less margin if an engine fails. The V-speeds convert that trade into hard numbers, computed for the actual weight, flap setting, runway, slope, wind, temperature and pressure of the day. They are not suggestions — performance regulations (and your type's AFM) make them the boundary conditions of a legal, safe takeoff.
V1 — takeoff decision speed
V1 is the maximum speed at which the takeoff can be rejected with the aircraft stopping within the remaining accelerate-stop distance — and, symmetrically, the speed by which the decision to continue must already be made following a failure. Two points the exam loves:
- V1 is a decision speed, not an action speed. By V1 the "stop or go" decision is complete. A failure recognised after V1 means the takeoff continues — rejecting above V1 risks a runway overrun.
- The callout protects the decision. "V1" is called so the crew knows the window to reject has closed; there is no time left to think.
V1 must never be less than VMCG (you must still be able to control the aircraft on the runway with an engine failed) and never greater than VR or VMBE (the maximum brake energy speed).
VR — rotation speed
VR is the speed at which the pilot flying begins to rotate to the takeoff attitude. It is sized so that, even with an engine failure at the worst moment, the aircraft reaches V2 at or before the screen height — 35 ft for Class A (transport category) aeroplanes.
- VR must not be less than V1 and not less than 1.05 × VMCA.
- Rotate at VR — no earlier. Rotating below VR lifts off below the scheduled speed, eroding stall and control margin and degrading the initial climb gradient.
V2 — takeoff safety speed
V2 is the target climb speed at screen height with one engine inoperative. It is the speed that delivers the required takeoff climb gradient in the most demanding case, and it anchors the whole climb-out: initial climb is flown at V2 until acceleration height.
- V2 must be at least 1.1 × VMCA and 1.2 × the stall speed VS (1.13 × VSR for modern reference stall speeds).
- Fly V2, not more. Chasing extra speed above V2 in the initial climb reduces the climb gradient the performance data assumed — a classic exam trap.
The control speeds behind them
Two further speeds bound the three above, and 032 Performance examines them directly:
- VMCG — minimum control speed on the ground: below it, with the critical engine failed, primary controls alone cannot keep the aircraft on the runway. Sets the floor for V1.
- VMCA — minimum control speed in the air: below it, the aircraft cannot be controlled in flight with the critical engine inoperative. Bounds VR (≥ 1.05 VMCA) and V2 (≥ 1.1 VMCA).
How examiners test the V-speeds
- Definitions verbatim. "V1 is the speed by which the decision to continue must be made" versus "the speed at which rotation is initiated" — one word swaps are the standard distractor.
- Relationship chains. VMCG ≤ V1 ≤ VR ≤ VMBE and V2 ≥ 1.1 VMCA / 1.2 VS. Know which speed limits which.
- Scenario logic. Engine failure recognised after V1 → continue; failure before V1 → reject and stop within ASDA; at screen height you must be at or above V2.
Frequently asked questions
Is V1 the speed at which you reject the takeoff?
No. V1 is the takeoff decision speed — the speed by which the decision to continue must already be made. A failure recognised after V1 means the takeoff is continued, because the remaining accelerate-stop distance can no longer be guaranteed.
What happens if you rotate before VR?
The aircraft lifts off below its scheduled speed, with reduced stall margin and a degraded initial climb gradient — and if an engine fails at that point, the aircraft may not reach V2 by the screen height.
Which speed must V2 never be lower than?
V2 must be at least 1.1 times VMCA and at least 1.2 times the stall speed VS (1.13 × VSR where reference stall speed is used). These minima guarantee controllability and stall margin with an engine inoperative.
Put it into practice
Want to train these exact questions? The ATPL Training question bank has exam-style V-speed and performance questions with worked explanations — free to start, on web and iOS. Try ATPL Training free.
Photo credit: Alf van Beem (Airplane-Pictures.net), via Wikimedia Commons — released into the public domain by the author.
